Home Appliance Problems & Solutions

Introduction

Most people use home appliances without thinking about their significant effect on daily life. However, everyone becomes very aware of their dependence on home appliances when they break down. If you face the same problem with a broken dryer, you can search for “dryer repair near me” and hire a professional to do the job for you. For now, let’s check out a few common appliance problems and figure out the solutions to fix them.

The Details

  1. Clothes come out warm, not dry – If your clothes come out of the dryer warm, yet wet, you may have overloaded the dryer. If that’s truly the case, remove a portion of the load and run it through the heating cycle again. If it still comes out wet, you have a faulty heating component. Apart from a faulty heating component, it may also be due to a clogged vent.

To fix this issue, unplug the dryer from the wall, remove the back panel and uninstall the faulty heating part. Disconnect the wires, install a new heating part, and put everything back. If this doesn’t help, you need to check the vent. Remove the dryer vent pipe and clean the lint cover. Warm the pipe and cover with warm soapy water and let it dry completely. After that, reattach them all and the problem should have been fixed.

  1. Dryer drum doesn’t spin – The humming of a dryer motor lets you know that the dryer is working properly. If you can hear the audible motor hum and the drum doesn’t spin, there may be something else that’s broken. If the motor isn’t faulty, the drum may not spin due to worn-out roller axles, drum rollers, drum glides, drum bearings, or a damaged drive belt.

To fix this issue, unplug the dryer from the wall and remove the rear panel. Inspect the roller axles, drum glides, belts, rollers, and bearings. If any part is worn out and doesn’t operate smoothly, you can get replacements from a local hardware store. If the drive belt is damaged, undo it from the hooks and the drum and replace it with a new one. After you’ve swapped out worn-out components, run the dryer to check if the drum is spinning.

  1. Leaky fridge – Leaking a refrigerator is a common yet dangerous problem since it may come in contact with electrical components or wires. You may have a leaky fridge due to a leaking water line, drain pan, high humidity inside the refrigerator or a clogged defrost line.

To fix a leaky refrigerator. Start by unplugging it and pulling it away from the wall. If it’s due to a filled-up drain pan, you can simply throw out the water and put it back. Otherwise, you need to remove all the items inside the refrigerator to avoid spoiling or contaminating them. Dig deep into the defrost drain with a plumbing snake and move it in and out to get rid of clogs. You can also use baking soda to unclog the drain and rinse it with a few cups of warm water.

  1. Faulty fridge, working refrigerator – Sometimes, the freezer inside the refrigerator breaks down while the refrigerator continues to work normally. Apart from a bad thermistor, this problem may also arise due to a damaged evaporator fan motor.

Start fixing this issue by checking the resistance on the thermistor with a multimeter. If there’s no continuity, you need to replace the thermistor. If that doesn’t fix the issue, you need to check the evaporator fan motor. Look for erratic movements and unusual sounds. Replace the motor if it doesn’t work properly.

  1. Dishwasher won’t start – Dishwashers don’t usually break down. However, if there is a blown fuse during use, the dishwasher won’t start. Apart from a blown fuse, or circuit, the problem may also lie with a faulty motor. Other causes of dishwasher not starting, include a faulty control panel, a defective door lock, and other component problems.

If it’s a blown circuit or fuse you need to disconnect power and check the fuse inside the control panel of the dryer. Remove the bad fuse and the control panel if it’s not working properly. Replace them with new components and the problem should be fixed. On the other hand, if it’s a stuck motor, try to rotate the fan with a stick. If it doesn’t work, the motor needs to be repaired by a technician or replaced. If it’s a defective door lock, identify the switch in the door panel and check for continuity with a multimeter. Replace it, if there’s no continuity.

  1. Bad odor from dishwasher – Food needs to be cleared out of the dishes before you put them inside the dishwasher. Otherwise, wet or old food particles may be lurking in the dishwasher and release a bad odor. Moreover, if you have put plastic dishes that weren’t supposed to go inside the dishwasher, the bad smell may be due to molten plastic.

To fix this issue, check the inside of the dishwasher for food debris. Use a toothpick or brush to remove those food particles. If there is stagnant water inside the dishwasher, drain it out completely and proceed to clean the insides of the dishwasher thoroughly with warm soapy water. After you’re done scrubbing, wipe it clean. Don’t miss out on the dishwasher screen either. Next, rinse the internal surface with hot water.

To avoid smelly dishwashers in the future, make sure to remove all food particles, crumbs, and chunks from the dishes, glasses, and cookware before you put them inside the dishwasher. It’s also important to not overload your dishwasher and avoid putting in plastic dishes that may melt due to high temperatures.

Conclusion

Home appliances are rigorously used in every life, and they would break down from time to time. Once you’re able to diagnose the problem, you can apply the above-mentioned solutions. Otherwise, you can take the convenient route and search for “dryer repair near me” to hire a reputable professional for the job.